50T Fixed Displacement Vane Pumps

50T fixed displacement vane pumps are developed and domestically by our company, featured by reasonable structure, good creditability, lower noise, advanced performance. They can be widely used in cutting machine, light industry machine, pressure machine,bearing machine, automated line machine and so forth.

0
Views: 209
contact us

Specifications

Model

Displacement
mL/r

Max.pressure
MPa

Speed
r/min

Weight kg

50T-4

4. 2

10

600-1800

10

50T-7

6. 5

50T-8

8. 5

50T-10

10.4

50T-12

13

50T-14

14.2

50T-17

16. 8

50T-20

19.4

50T-23

23. 3

50T-25

24. 4

50T-30

30. 5

50T-36

36. 0

50T-39

38.6

Model Code

Installation and Use

1. In installation, the tolerance of concentricity between shaft of pump and motor must be less than 0.10mm(TIR) and the maximum permissible angle error is less than 0.2 degrees by using the flexible coupling; The pump shaft shall not bear the radial and axial load ; The carrier must be firm with good rigidity and can fully absorb vibrations.

2. If a pump is used at speed below 1200 r/min, install the pump with the suction port upside so that the pump can suck up fluid easily at starting.

3. Fix pipes, especially inlet pipes in accordance with the size of port and assemble safety relief valves in the system; The regulating pressure of the safety valve shall not be greater than the maximum pressure of the pump; Inlet pipes must be strictly sealed with no leakage; The fuel tank shall be equipped with a diaphragm to separate the bubbles and dirt from the oil; The oil return nozzle should be lower the fluid surface, the minimum depth of 50 mm, even in a low, too, when the permissible level of to avoid the formation of bubbles .

4. Oil should be kept clean, pipes and tanks must be thoroughly cleaned; Precise filters should be assembled with the advised precision of 25μm in the system, the cleanness level of oil should be within NSA12. Fix the sufficient-volume filter (the rated flow rate should be greater than twice the pump flow) at the inlet of the pump 50mm above the bottom of the tank, with the suggested precision of 100μm(150 mesh).

5. Selection of hydraulic oil:This series pumps are applicable to various oil liquids, including petroleum series oil, Water-cut hydraulic fluid, synthetic hydraulic fluid etc。However, the specifications of the pumps such as maximum pressure and maximum pump speed may be changed according to the type of hydraulic fluids to be used. For details, please refer to the specifications of the pump concerned.

To improve the pump performance, prolong service life, it is recommended to use anti-wear hydraulic oil (such as ISO VG32 or ISO VG46).When the oil viscosity 30 cSt is the best (to keep the oil temperature within 10 ~ 60 ℃ , the best is 35 ~ 50 ℃ ), especially to avoid high temperature continuous operation, otherwise the pump will shorten the service life, set the heater and cooler when necessary to adjust the oil temperature.

 

Antiwear water glycol fluid

Grades of Special oil

Manufacturer

Brand

Manufacturer

Brand

Showa Shell Sekiyu K.K.

Shell HFC Fluid 46

Mobil Sekiyu

Mobil DTE 24,25

JX Nippon Oil & Energy Corp.

Hyrando FRZ46

Showa Shell Sekiyu

Shell Tellus Oil 32,46

M O R E S C O Corp.

Hydol HAW

 

 

Cosmo Oil Lubricants Co.,Ltd

COSMO FLUID GS46, HQ46

 

 

 

6. Fluid viscosity and temperature and maximum viscosity for low start-up speed.

 

Viscosity and temperature of oil

Max. viscosity limit at low speed start

Oil type

Oil temperature

Viscosity
mm 2 /s(cSt)

Oil pump model

Starting speed
r/min

Max.viscosity
mm 2 /s(cSt)

Petroleum oil

0~70

20~400

PV2R1、PV2R21、
PV2R31

750

100

Phosphate ester fluid

950

200

Water glycol fluid

0~50

PV2R2

600

100

Water-oil emulsions

0~50

PV2R3、PV2R32

950

200

 

7. Set the suction pressure at pump inlet port at the value given in the table below(in relation to the rotating speed of the pump, the minimum suction pressure may be restricted for a certain nominal displacement). In case where the pump is installed on the tank or at the position higher than the tank top cover, the height of the suction port of the pump should be less than 500mm.

 

type

Suction pressure is allowed

Min.

Max.

Petroleum base hydraulic oil

Phosphoric acid grease and aqueous hydraulic fluid

PV2R single pump

PV2R1、PV2R2 PV2R3

-20kPa

-16kPa

+30 KPa

PV2R double pump

PV2R21 PV2R31、PV2R32

 

Note: PV2R3-116, 125, 136 pumps, when the speed is greater than 1700r/min, the minimum suction port pressure is 0KPa.


8.Check the inlet,outlet and direction of rotation before starting the pump. Turn the shaft of pump evenly and nimbly by hand after fixing the pump. It is best to fill the pump with oil for the first time.

At an initial operation or at an operation after a long rest, the pump may have difficulty in sucking up fluid; In such cases, an air bleed valve should be installed beforehand on the discharge side or discharge air by slightly slackening the connection on the discharge side. At starting, operate the pump intermittently as far as possible with no load.

9. At startup, If the oil viscosity is higher than the suitable viscosity (54cSt), the pressure should be limited to 50% or less of their respective rated values until the system has warmed up.

Install Connection Dimensions

Flange mounting type

 

Foot mounting type

Leave a MessageIf you have any questions about our machine, please do not hesitate to contact us.

  • captcha